产品中心
C-UV 4216 Technical Data Sheet
UV/Visible light cure Adhesive 紫外/可见光固化胶粘剂
PRODUCT DESCRIPTION 产品介绍
C-UV 4216 is basically dsigned for bonding rigid or flexible PVC to PC. It enable easy assembly of components with close assembling tolerance(i.e. joining PC to flexible PVC tubing). The product has shown excellent adhesion to a wide vriety of substrates including glass, PET, PMMA and most metals. C-UV 4216是一种主要涉及用来粘结坚硬或柔韧PVC材料与PC材料。它具有的特性使得组建能够完整结合(例如PC与PVC管材),该材料还对玻璃,PET,PMMA等塑料和大多数金属都表现出良好的粘结性能
PROPERTIES OF UNCURED MATERIAL 固化前材料性能
Property性能 |
Test Method测试方法 |
Value数值 |
Color/Appearance 颜色/外观 |
Visual 目测 |
Beige translucent 米黄色或透明液体 |
Specific Gravity 比重, 25 °C, g/cm3 |
ASTM D-792 |
1.1
|
Viscosity 粘度, cps, 25 °C |
Brookfield 布氏粘度, 10 rpm |
200–400 |
Refractive index 折射率 |
|
1.48 |
Shelf life 储存期@20 °C, month |
|
12 |
TYPICAL PROPERTIES OF CURED MATERIAL 固化后材料典型物理性能
Material cured@365nm at 80 sec x 30 mW/ cm2 该产品在30 sec x 100 mW/ cm2下固化@365nm
Property性能 |
Test Method测试方法 |
Value数值 |
Hardness 硬度 |
Shore D 邵氏硬度 |
65 |
Refractive index 折射率 |
|
1.51 |
Fixture time, glass slide 固定时间,玻璃片 |
6 mW/ cm2@365nm |
< 15seconds |
Depth of cure 固化深度 |
20 seconds x 30 mW/ cm2 |
4 mm |
Tensile strength 抗拉强度, N/mm2 |
ISO 527 |
22.7 |
Elongation 延长率, % |
|
265 |
Adhesive strength, Block Shear 粘接强度, 剪力, N/mm2 |
90 seconds x 30 mW/ cm2 |
25 (PC/PC) 6 (PC/glass) 13 ( PC/PVC) |
Aging test, PC/PVC/Aluminum 老化测试, PC/PVC/铝 |
50 °C /100%RH x168 hrs |
80-85% retention 保持 |
Volume resistivity 体电阻, Ω.cm |
|
8.5E+14 |
HEAT AGING 热老化测试
Lap Shear Strength 搭接剪切强度 aged at temperature indicated and test 22℃,在22℃下测试
Condition 条件 |
% of initial strength retained 与初始比较对比的百分比 |
Aged@ 71℃ for 170 hours 71℃下170小时 |
100 |
Aged@ 71℃ for 340 hours 71℃下340小时 |
100 |
Aged@ 93℃ for 170 hours 93℃下170小时 |
100 |
Aged@ 93℃ for 340 hours 93℃下170小时 |
100 |
CHEMICAL/SOLVENT RESISTANCE 耐化学/溶剂性能
Aged under conditions indicated and test@22℃, 在22℃下测试
|
|
% of initial strength 剩余强度 |
||
Eviroment 条件 |
℃ |
2h |
24h |
170h |
Water immersion 水浸 |
49 |
|
|
100 |
Water immersion 水浸 |
87 |
|
|
65 |
Boiling water 沸水 |
100 |
100 |
|
|
Isopropanol 异丙醇 |
22 |
|
100 |
|
Heat/humidity 热/湿 |
38 |
|
|
100 |
DIRECTIONS FOR USE 使用指南
The adhesive can be hand applied from bottle, or dispensing systems are also available for high volume assembly applications. 该产品可手工从瓶中取出使用,对于大体积的装配生产可提供分散系统。
Apply adhesive to one surface and assemble immediately.将该产品施加在一个部件的表面上后立即装配
Curing time table 固化进度表
The material cures when exposed to ultraviolet radiation and/or visible light with sufficient intensity. Recommended intensity for cure is 30-100 mW/ cm2 at 365 nm. It needs at least 80 seconds in在30 mW/ cm2 at 365 nm. 在足够强度的紫外和(或)可见光辐照下该产品可固化。推荐固化光强度为30-100 mW/ cm2 at 365 nm。在30 mW/ cm2 at 365 nm 下至少固化80秒
STORAGE INFORMATION 储存方法
Store at 8 – 20 °C in a dry, cool place and in sealed containers out of direct sunlight. 在8 – 20 °C下干燥,凉爽和密封保存,避免阳光的直接照射。
Notes 注意: it is the user’s responsibility to determine the suitability of the products and methods of use. 用户具有决定产品的适用性和选择合适的使用方法的责任。